JH1660 Main parameters
Model | JH1660 |
Length | 1650mm |
Pipe Diameter | 60±1mm |
Wavelength | 10.6um |
Catalyst coated | Yes |
Output Power Stable Value | 80W |
Max Output Power | 130W |
Triggering Voltage | 26-28KV |
Working Voltage | 20-23KV |
Triggering Current | 4-5mA |
Max Working Current | 30mA |
Type Of Cooling | Water-cooling 15-25℃ |
Spot diameter | 7±1mm |
Packing size | 1800mmx160mmx150mm |
Laser power will be attenuated when the Laser Tube is used at a certain time; If the laser is pink, it is in normal condition; if the laser is white, it means the laser power is attenuate.
Installation Instruction
1) In order to fully circulate the cooling water of the laser tube, it is necessary to ensure that the water flow enters from the low point and drain away from the high point under the pressure of the water so as to achieve the cooling of the entire laser tube.
2) If the flow direction is opposite, it is possible that the cooling water can not fill the whole pipe,resulting in poor cooling,power reduction and the phenomenon of tube burst.
3)If there is air bubbles in the laser tube,before the dimming,lift the water outlet side,until the bubble is completely discharged, and then fixed laser tube,please be careful not to allow residual bubbles in the laser tube.On the one hand, it will affect the light effect, on the other hand, it will lose the laser power. If the laser tube is poor cooling caused by bubble for long time, it may burst.
H-Series:Main Parameters
Type | Length (mm) | Dia (mm) | Rated Power (W) | Max Power (W) | Warranty (Months) |
H-600 | 600 | 50 | 30 | 40 | 6 |
H-700 | 700 | 50 | 40 | 50 | 6 |
H-800 | 800 | 50 | 40 | 50 | 6 |
H-1000 | 1000 | 50 | 50 | 80 | 6 |
H-1260 | 1250 | 60 | 60 | 90 | 6 |
H-1280 | 1250 | 80 | 80 | 100 | 10 |
H-1480 | 1450 | 80 | 100 | 120 | 10 |
H-1680 | 1650 | 80 | 130 | 150 | 10 |
H-1660 | 1650 | 60 | 80 | 130 | 10 |
H-1880 | 1850 | 80 | 150 | 180 | 10 |
V-Series:Main Parameters
Type | Length (mm) | Dia (mm) | Rated Power (W) | Max Power (W) | Warranty (Months) |
V-1280 | 1250 | 80 | 80 | 105 | 12 |
V-1480 | 1450 | 80 | 100 | 125 | 12 |
V-1680 | 1650 | 80 | 130 | 155 | 12 |
V-1880 | 1850 | 80 | 150 | 180 | 12 |
K-Series:Main Parameters
Type | Length (mm) | Dia (mm) | Rated Power (W) | Max Power (W) | Warranty (Months) |
K-1280 | 1250 | 80 | 80 | 110 | 18 |
K-1480 | 1450 | 80 | 100 | 130 | 18 |
K-1680 | 1650 | 80 | 130 | 160 | 18 |
K-1880 | 1850 | 80 | 150 | 190 | 18 |
D-Series:Main Parameters (co2 laser marking machine)
Type | Length (mm) | Dia (mm) | Rated Power (W) | Max Power (W) | Warranty (Months) |
D-1280 | 1250 | 80 | 80 | 100 | 12 |
D-1480 | 1450 | 80 | 100 | 120 | 12 |
1. Long Life and Stable Power
J H CO2 laser tube have a serious of special patents, combined with catalytic technology, the life and power have been greatly increased. Such as the J H CO2 laser tube 150 w ,it’s max output power can reach about 180 w. Other company’s CO2 laser tube merely can beyond us.
2. Fast Cutting Speed
J H Laser have improved the quality all the time, J H LASER CO2 laser tube’s cutting speed is apparently faster than others in the same power. When cutting white fabric, it can not yellow.
3. Good Beam Mode
J H Laser beam mode is better, using own patented technology to modify the beam size and quality effectively that solves the beam distortion, increase the effective power. which is up to TEM00.
4. Light Weight
To compared J H LASER CO2 laser tube with the same other general Co2 laser tube, Our J H LASER CO2 laser tube’s weight is lighter than others’. which will help enterprise to have a more diversify application on CO2 laser tube
5. Strictly Test process
J H CO2 laser tube have been tested by 18 times techical process strictly, the breakage rate is lower 3%
6. Long Warranty
We provide 7*24hours 1 TO 1 After-Service, we committed that our J H LASER tubes 150w have 6 months warranty to you.
7. Competitive Price
J H LASER CO2 laser tube have providing competitive price for all customers, we think our products can make you satisfaction.
content is empty!